Anatase tio2 nanoparticles with exposed {001} facets for efficient dye-sensitized solar cells

ABSTRACT Anatase TiO2 nanoparticles with exposed {001} facets were synthesized from Ti powder _via_ a sequential hydrothermal reaction process. At the first-step hydrothermal reaction,

H-titanate nanowires were obtained in NaOH solution with Ti powder and at second-step hydrothermal reaction, anatase TiO2 nanoparticles with exposed {001} facets were formed in NH4F

solution. If the second-step hydrothermal reaction was carried out in pure water, the H-titanate nanowires were decomposed into random shape anatase-TiO2 nanostructures, as well as few

impurity of H2Ti8O17 phase and rutile TiO2 phase. Then, the as-prepared TiO2 nanostructures synthesized in NH4F solution and pure water were applied to the photoanodes of dye-sensitized

solar cells (DSSCs), which exhibited power conversion efficiency (PCE) of 7.06% (_V_OC of 0.756 V, _J_SC of 14.80 mA/cm2, FF of 0.631) and 3.47% (_V_OC of 0.764 V, _J_SC of 6.86 mA/cm2, FF

of 0.662), respectively. The outstanding performance of DSSCs based on anatase TiO2 nanoparticles with exposed {001} facets was attributed to the high activity and large special surface area

for excellent capacity of dye adsorption. SIMILAR CONTENT BEING VIEWED BY OTHERS MOF-DERIVED CO2+-DOPED TIO2 NANOPARTICLES AS PHOTOANODES FOR DYE-SENSITIZED SOLAR CELLS Article Open access

11 August 2021 PHOTOVOLTAIC PERFORMANCE OF MOF-DERIVED TRANSITION METAL DOPED TITANIA-BASED PHOTOANODES FOR DSSCS Article Open access 18 April 2023 INNOVATIVE MICROWAVE IN SITU APPROACH FOR

CRYSTALLIZING TIO2 NANOPARTICLES WITH ENHANCED ACTIVITY IN PHOTOCATALYTIC AND PHOTOVOLTAIC APPLICATIONS Article Open access 01 June 2024 INTRODUCTION Dye-sensitized solar cells (DSSCs),

since the first report by Grätzel in 1991, have captured a lot of attentions due to the advantages of high power conversion efficiency (PCE), low cost, friendly to the environment and simple

fabrication process1,2,3. Traditionally, standard DSSC structure is the combination of photoanodes, dye sensitizers, redox electrolytes and counter electrodes4,5,6. There, the photoanodes

strongly affect the performance of DSSCs, which serve as scaffolds for dye molecules and the transport media for photo-generated electrons7,8,9,10. As a result, considerable efforts have

been devoted to pursuing a more effective photoanode. Titanium dioxide (TiO2) is the shared material for photoanode in DSSCs, because of the high chemical and optical stability, low toxicity

and appropriate band structure11,12,13. In DSSCs, the performance profoundly depends upon the morphology, crystalline phase, structure and exposed crystal facet of TiO214,15,16. The

previous studies indicated that anatase TiO2 single crystal with exposed {001} facets has good potency for dye adsorption and charge transfer17. Both theoretical and experimental studies

showed that {001} facets of anatase TiO2 single crystal are extraordinarily reactive18 and the surface energy is 0.90 J/m2, which is much larger than 0.44 J/m2 surface energy of the usual

{101} facets19. To date, there have been a large number of reports for preparing anatase TiO2 single crystal with appropriately exposed {001} facets for application of enhanced DSSCs, such

as TiO2 nanotube20, anatase TiO2 nanosheets21, yolk@shell anatase TiO2 hierarchical microspheres22 and mesoporous TiO2 single crystals9. Yet it was reported that the ratio of {001} and {101}

facet has impact on the performance of nanodevice because of the “surface heterojunction” of {001} and {101} surfaces, where appropriate but not great proportion of {001} facets is

beneficial to the transfer and separation of photogenerated electrons and holes23,24. Nowadays, the efficiency of DSSCs has been achieved 13% through the molecular engineering of porphyrin

sensitizers25. It’s worth noting that the photoanode is TiO2 nanoparticle film because of the large specific surface area for loading dye molecules. To the best of our knowledge, it is a

challenge to synthesize TiO2 nanoparticles with appropriately exposed {001} facets, which is the desired material for photoanodes of DSSCs. In this work, anatase TiO2 nanoparticles with 34%

exposed {001} facets were synthesized _via_ a two-step hydrothermal reaction method from Ti powder, which were further developed as efficient photoanodes for DSSCs. The first-step

hydrothermal reaction of Ti powder in NaOH solution led to the formation of H-titanate nanowires after washing with HCl solution26 and the second-step hydrothermal reaction resulted in the

formation of anatase TiO2 nanoparticles with exposed {001} facets in NH4F solution or random shape TiO2 nanostuctures with tiny impurity phase in pure water. Subsequently, the obtained TiO2

nanostructures were utilized as photoanodes of DSSCs, yielding PCE of 7.06% (_V_OC of 0.756 V, _J_SC of 14.80 mA/cm2, FF of 0.631) and 3.47% (_V_OC of 0.764 V, _J_SC of 6.86 mA/cm2, FF of

0.662), respectively. The result indicated the anatase TiO2 nanoparticles with 34% exposed {001} facets possess the characteristics of high activity and large special surface area for the

excellent capacity to load dye molecules. RESULTS STRUCTURE OF ANATASE TIO2 NANOPARTICLES Figure 1(a) shows the powder XRD patterns of the as-grown H-titanate nanowires (I), as well as the

obtained TiO2 nanostuctures synthesized in pure water (II) and in NH4F solution (III). In curve (I), there are several broadened diffraction peaks, which correspond well to the H2Ti5O11·H2O

phase (PCPDFWIN, 44-0130). Thus, the Ti powder was reacted with NaOH solution, after washing with dilute HCl solution, the obtained sample was H2Ti5O11·H2O. Taking the H2Ti5O11·H2O nanowires

as precursor in the following hydrothermal treatment in pure water, the obtained powder was mainly indexed as anatase TiO2 phase, as revealed in curve (II). Meanwhile, the another peaks

besides anatase TiO2 phase indicate that the H2Ti5O11·H2O nanowires were not completely decomposed into pure anatase TiO2 phase. The peaks located at 27.71°and 41.86° were corresponded to

(012) and (860) planes of H2Ti8O17 phase, respectively (PCPDFWIN, 36-0656). While the peaks located at 36.13° and 56.55° were assigned to (101) and (220) planes of rutile TiO2 phase

(PCPDFWIN, 87-0710). More importantly, if the further hydrothermal reaction was taken in NH4F solution, a pure phase of anatase TiO2 (PCPDFWIN, 84-1286) was observed as the curve (III).

Using the Scherrer equation, the average crystal size of anatase TiO2 nanostructures obtained in NH4F solution was about 45 nm estimated from the full width at half maximum of the (101)

peak. Since no other diffraction peaks belonging to impurities are observed, suggesting that all the H2Ti5O11·H2O nanowires were completely converted to anatase TiO2 phase in NH4F solution.

The diffraction peaks of curve (III) are sharper than that of curve (II), indicating the better crystallization and larger crystallites due to the enhanced effect of F−25. The obvious (004)

diffraction peak of curve (III) suggests dominant crystal growth along the [001] direction26, which is typical for anatase TiO2 nanoparticles with exposed {001} facets. In order to

quantitatively analyze the percentage of {001} facets, Raman spectroscopy was carried out as shown in Fig. 1(b)24,27. The peaks at 144, 394, 514 and 636 cm−1 suggest the typical anatase TiO2

phase, being consistent with the XRD results. The percentage of {001} facets was calculated as 34% by measuring the peak intensity ratio of the Eg (at 144 cm−1) and A1g (at 514 cm−1)

peaks27. Figure 2 shows typical scanning electron microscopy (SEM) images of the TiO2 synthesized in pure water and in NH4F solution. After hydrothermal reaction and washing with HCl

solution, the morphology of the as-prepared H2Ti5O11·H2O was nanowire structure (Supplementary Information Fig. 1S). After the further hydrothermal treatment at 200 °C for 48 h, the

morphology of the H2Ti5O11·H2O nanowires undergone significant change. The H2Ti5O11·H2O nanowires were decomposed into random shape TiO2 nanostructures in pure water, as shown in Fig. 2

(a,b). There was complex morphology of nanorod, nanosphere, nanoellipsoid, irregular nanostructures, _etc_. Interestingly, the morphology of the TiO2 obtained in NH4F solution was regular

nanoparticles with size of ~50 nm as illustrated in Fig. 2(c,d), in good agreement with the XRD measurement. The NH4F as morphology controlling agent led the H2Ti5O11·H2O nanowires to

completely decomposing into regular TiO2 nanopaticles27. The transmission electron microscopy (TEM) was used to further characterize the crystal structure and morphology of H2Ti5O11·H2O and

TiO2 nanostrctures in Figure 3. Fig. 3(a,b) shows the H2Ti5O11·H2O nanowire sample. The lattice fringes with distances of 0.940 nm in the HRTEM image of Fig. 3(b) corresponded well with

(200) plane of H2Ti5O11·H2O phase. Figure 3(c) shows TEM image of random shape TiO2 nanostructures by the further hydrothermal reaction in pure water. The HRTEM image (Fig. 3(d))

corresponding the dark red-box area shows interplanar spacing of 0.352 nm, which matches well with (101) plane of anatase TiO2. When the second-step hydrothemal reaction was taken in NH4F

solution, the H2Ti5O11·H2O nanowires were decomposed into regular TiO2 nanopaticles (Fig. 3(e)). The HRTEM image corresponding the cyan-box area in Fig. 3(e) was revealed in Fig. 3(f), where

the interplanar spacing of 0.192 and 0.237 nm corresponded to (200) and (004) planes of anatase TiO2, respectively. In addition, the (004) plane indicated the anatase TiO2 single crystal

with exposed {001} facets and the shape of anatase TiO2 was truncated octahedron. Further, the {101} facets could be also observed through TEM technique (Supplementary Information Fig. 2S).

GROWTH MECHANISM Figure 4 illustrates the schematic of the preparation process of random shape TiO2 nanostrctures and truncated octahedron TiO2 nanoparticles with exprosed {001} facets _via_

a two-step hydrothermal reaction process. At the first-step hydrothermal reaction, Ti powder reacted with NaOH to synthesize Na-titanate nanowires. Followed by washing with diluted HCl

solution, the Na-titanate nanowires were transformed into H-titanate nanowires _via_ cation exchange reaction. At the second-step hydrothermal reaction, the H-titanate nanowires precursors

was under gone completely change in aqueous solution with or without NH4F. In this process, the H-titanate precursors experienced a dissolution and nucleation process during the hydrothermal

treatment28. In pure water, the dissolution occurred without any restraint, thus TiO2 nanostructures with random shape distribution were obtained. Moreover, the nucleation was not thorough

and there was few H2Ti8O17 phase and TiO2 rutile phase. When the H-titanate precursors were performed dissolution and nucleation in NH4F solution, single crystal anatase TiO2 nanoparticles

with exposed {001} facets were obtained. At the dissolution process, the existing of F− ions could be bonded with Ti atom to reduce the surface energy of the {001} facets to lower than that

of the {101} facets, resulting in exposing {001} facets during nucleation29,30. Besides, F− ions acted as morphology controlling agent to control the shape of TiO2 nanostructures during

nucleation and the shape of TiO2 nanoparticles was truncated octahedron, as shown in Fig. 4. CHARACTERIZATION OF PHOTOVOLTAIC PERFORMANCE The obtained TiO2 powders were mixed with some

additive agents to make TiO2 pastes and then the TiO2 pastes were coated on TiCl4-treated FTO glasses by doctor-blading method to realize photoanodes after annealing. The thickness of the

TiO2 photoanodes was 13.5 μm (Supplementary Information Fig. 3S). Figure 5(a) indicates the current density-voltage (I-V) curves of the DSSCs based on random shape TiO2 nanostructures (noted

“Without F−”) and truncated octahedron TiO2 nanoparticles with 34% exposed {001} facets (noted “With F−”). Table 1 listed the corresponding detailed photovoltaic parameters, including the

open-circuit voltage (_V_OC), short-circuit current density (_J_SC), fill factor (FF) and PEC. The larger PCE 7.06% of DSSCs (noted “With F−”) was mainly rooted in the _J_SC, which increased

from 6.86 to 14.80 mA/cm2. Generally, _J_SC can be approximated as following expression31: where _e_ is the elementary charge, ηl_h_ is the light-harvesting efficiency related to the amount

of adsorbed dye molecules and the light-scattering properties, η_inj_ is the charge-injection efficiency, η_cc_ is the charge-collection efficiency relied on competition between charge

recombination and collection and _I__0_ is the light flux. Here, η_inj_ is suggested to be of the same value, because of the injection both from the TiO2 material to N719 dye.

Electrochemical impedance spectroscopic (EIS) measurements were conducted in the dark under a bias of 0.75 V to evaluate the charge transfer and recombination as the Nyquist plots in Fig.

5(b)32. The radius of semicircle in Nyquist plots revealed the charge-transfer resistance (_R_ct) between TiO2/dye/electrolyte interfaces. The slightly larger one based on the random shape

TiO2 nanostructures (Without F−) indicated a slow charge recombination at the TiO2/dye/electrolyte interfaces. Namely, the electron lifetime in photoanodes based on the random shape TiO2

nanostructures was slightly longer. Moreover, the electron lifetime (τ) was calculated using the following equation33,34: where _C__u_ is the corresponding chemical capacitance. The

corresponding values of _R_ct (243.3 and 237.1 Ω) and _C__u_ (7.5534 × 10−4 and 7.1165 × 10−4 F) can be obtained by simulation using the Zview software. The electron lifetime was 0.184

(Without NH4F) and 0.179 s (With F−) of DSSCs, respectively. Meanwhile, the open-voltage decay method was employed to further investigate the electron lifetime of the two cells, as shown in

Fig. 5(c). From the open-voltage decay rate, the electron lifetime (τ) can be calculated by the following equation35,36: where _k__B_ is the Boltzmann constant and _T_ is room temperature.

The calculated data of τ were plotted in Fig. 5(d). It was observed that the electron lifetime based on random shape TiO2 nanostructures was slightly longer than that based on TiO2

nanoparticles. The possible reason was that there were some nanorods and relatively large nanoparticles in random shape TiO2 nanostructures, which were in favour of charge transfer.

Therefore, it dos no outstanding difference to the charge transfer and the value of η_cc_ of DSSCs (noted “Without NH4F”) was little larger than that one (noted “With NH4F”). In other words,

the increasing of _J_SC at over twice was not from the factor of η_cc_. It is well-known that the nanoparticle films have large special surface area to load more dye molecules1. Therefore,

the special surface area was checked by Brunauer-Emmett-Teller (BET) data as shown in Fig. 6(a). The BET surface area was measured as 40.9 and 44.6 m2/g for random shape TiO2 nanostructures

and TiO2 nanoparticles, respectively. The special surface area of TiO2 nanoparticles was slightly bigger than that of the random shape TiO2 nanostructures. More importantly, exposing highly

reactive {001} facets of TiO2 can enhance dye adsorption17. Thus, we investigated the amount of absorbed dye molecules to elucidate the factor of ηl_h_. The optical image of TiO2 and

sensitized-TiO2 films on FTO substrates was shown as the inset in Fig. 6(b). The color of random shape TiO2 nanostructure films (i) was lutescent, while the color of TiO2 nanoparticle films

(ii) was pure white. After being sensitized by N719 dye, the color of the sensitized-TiO2 films based on TiO2 nanoparticles (iv) was darker red than that of based on random shape TiO2

nanostructures (iii), indicating that the TiO2 nanoparticles with exposed {001} facets absorbed more dye molecules. The UV-vis absorbance measurements in Fig. 6(b) revealed the

sensitized-TiO2 films based on TiO2 nanoparticles (iv) had a stronger visible absorption, because of more amount of loading dye molecules. The absorbed dye amounts were calculated from

UV-vis absorbance measurements of the concentration desorbed N719 dye in NaOH solution by using Lambert-Beer’s Law37,38. The absorbed dye amount of photoanodes based on TiO2 nanopartiles

with exposed {001} facets was about four times than that of based on random shape TiO2 nanostructures, as listed in Table 1. The TiO2 nanoparticles with exposed {001} facets had excellent

capacity for adsorption of dye molecules. As a consequence, anatase TiO2 nanoparticles with exposed {001} facets were efficient photoanodes for DSSCs. DISCUSSION Anatase TiO2 nanoparticles

with 34% exposed {001} facets have been successfully synthesized from Ti powder _via_ two-step hydrothermal reaction process. The first -step hydrothermal reaction was alkaline hydrothermal

reaction to obtain H-titanate nanowires. At the second-step hydrothermal reaction, the H-titanate nanowires were decomposed into random shape anatase TiO2 nanostrctures with few impurity in

pure water or truncated octahedron anatase TiO2 nanopaticles with 34% exposed {001} facets in NH4F solution. The DSSCs based on anatase TiO2 nanopaticles with 34% exposed {001} facets showed

outstanding performance of efficiency 7.03%, which was about twice than that of based on random shape TiO2 nanostructures. The high performance was ascribed to that the anatase TiO2

nanopaticles with 34% exposed {001} facets own high activity and large special surface area for excellent capacity of absorbing dye molecules. We anticipate that the anatase TiO2

nanopaticles with 34% exposed {001} facets open up a promising avenue for efficient TiO2-based photoelectric nanodevices. METHODS MATERIALS Fuorinated tin oxide (FTO, ~7 Ω/cm2) glasses were

bought from Nippin Sheet Glass Co., Ltd. Sodium hydroxide (NaOH, 96.0%), titanium tetrachloride (TiCl4, 99.0%), ammonium fluoride (NH4F, 96.0%), hydrochliric acid (HCl, 36%~38%wt), ethanol

(99.7%) and acetone (99.5%) were purchased from Sinopharm Chemical Reagent Co. Ltd. Ruthenium 535-bisTBA (N719) was purchased from Solaronix. Guanidinium thiocyanate (GuSCN, 99.0%) was from

Amresco. Titanium powder (Ti, 99.99%), lithium iodide (LiI, 99.999%), iodine (I2, 99.99%), 1-methyl-3- propylimidazolium iodide (PMII, 98%), 4-tert-butylpyridine (4-TBP, 96%) and tert-butyl

alcohol (99.5%) were obtained from Aladdin. Acetonitrile (99.8%) and valeronitrile (99%) were from Alfa Aesar. All solvents and chemicals were reagent grade and were used without further

purification. SYNTHESIS OF H-TITANATE NANOWIRES Na-titanate nanowires were firstly synthesized by alkali hydrothermal reaction of Ti powder in NaOH solution. First, 70 mL of 10 M NaOH

solution was obtained under magnetic stirring. Then 0.2 g Ti powder was added into the above NaOH solution and stirred for 10 minimums again. The final solution was transferred to a 100 ml

Teflon-lined stainless steel autoclave and loaded into an oven. The temperature was set 210 °C for 48 hours and then cooled down to room temperature naturally. After the hydrothermal

treatment, the obtained Na-titanate nanowires were completely washed with 0.1 M HCl solution to replace Na+ with H+. Subsequently, the H-titanate nanowires were washed with deionized water

several times. SYNTHESIS OF ANATASE TIO2 NANOPATICLES WITH EXPOSED {001} FACETS The above total H-titanate nanowires were added into 100 mL Teflon-lined stainless steel autoclave containing

70 ml deionized water with or without adding 0.25 M NH4F. Afterward, the autoclave was loaded into an oven at 200 °C for 48 hours and then cooled down to room temperature naturally. After

the hydrothermal reaction, the obtained TiO2 powders were collected from the solution and washed with deionized water and ethanol for several times by centrifugation. Finally, the powders

were dried at 80 °C over night. The obtained dry powder was anatase TiO2 nanopaticles with exposed {001} facets in NH4F solution or random shape TiO2 nanostuctures with few impurity in pure

water. PREPARATION OF TIO2 PHOTOANODE 1 g TiO2 powder was mixed evenly under magnetic stirring in a mixture of 0.2 mL acetic acid, 3.0 g terpineol, 0.5 g ethyl cellulose and some ethanol to

form a slurry, the slurry was milled in a mortar for about 20 min and then dispersed with ultrasonic for 10 min to prepare viscous white TiO2 paste. The FTO glasses were washed with

detergent and sonicated in deionized water, acetone and ethanol for 20 min, respectively. After dried under flowing argon gas, the cleaned FTO glasses were soaked into 0.04 M TiCl4 solution

at 70 °C for 30 min to form a compact TiO2 layer and then rinsed with deionized water and ethanol. The TiO2 pastes were printed onto the TiCl4-treated FTO glasses by doctor-blading method.

Then the printed TiO2 layers were annealed at 125 °C for 15 min, at 325 °C for 5 min, at 375 °C for 5 min, at 450 °C for 15 min and then at 500 °C for 15 min in a muffle furnace. The

annealed TiO2 layers were immersed into 40 mM TiCl4 solution at 70 °C for 30 min again and after being rinsed with deionized water and ethanol, the films were sintered at 500 °C for 30 min

in muffle furnace. After the temperature was cooled to about 80 °C, the TiO2 pohtoanodes were immersed into 0.5 mM N719 dye in acetonitrile/tert-butanol (V:V/1:1) and kept for 16 h at room

temperature. The sensitized TiO2 photoanodes were washed with acetonitrile to remove the possible physically-adsorbed dye molecules. FABRICATION OF DSSCS The Pt counter electrodes were

deposited by magnetron sputtering on cleaned FTO glasses. Sputtering was performed using a Pt (99.99% purity) target in an Ar ambient atmosphere at 100 W. For fabricating DSSCs, the Pt

counter electrodes were buckled on the sensitized-TiO2 photoanodes, which were sealed using a 50 μm plastic sheet and the internal space was filled with a liquid electrolyte. The electrolyte

was composed of 0.6 M PMII, 0.05 M LiI, 0.03 M I2, 0.1 M GuSCN and 0.5 M 4-TBP in acetonitrile and valeronitrile (V:V/85:15). The active area of the solar cell was 0.15 cm2 without a mask.

MEASUREMENT The crystal structure and phase purity of the obtained powders were investigated using a powder X-ray diffractometer (XRD, PANalytical B.V., The Netherlands) with Cu-Kα (λ = 

0.15418 nm) radiation. Raman measurement was carried out using a Raman spectroscopy (LABRAM HR800, France) with a 514.5 nm argon ion laser of 200 μm spot size for excitation. The size and

morphology of the samples were recorded by field emission scanning electron microscopy (SEM, FEI NOVA NanoSEM 450). Transmission electron microscopy (TEM) and and high-resolution TEM (HRTEM)

images were performed by TEM (FEI Tecnai G2 20 UTwin) or aberration-corrected TEM (FEI Titan G2 60-300). The sample was prepared by drop casting ethanolic dispersion of tiny TiO2 powder

onto a carbon coated Cu grid. The Brunauer-Emmett-Teller (BET, V-Sorb 2800P) was carried out to measure the surface area of the samples. The current density-voltage (_I-V_) measurements,

open-voltage decay measurements and electrochemical impedance spectroscopy (EIS) measurements were performed by an Autolab electrochemic workstation (modelAUT84315, The Netherlands). UV-Vis

absorption spectrometry (UV-2550, Shimadzu) was employed to test the absorption spectra. The illumination intensity was AM 1.5G (100 mW/cm2, calibrated with a Si photodiode) using a solar

simulator (Newport, USA). The electrochemical impedance spectroscopy (EIS) measurements were scanned in dark condition at a bias of 0.75 V with an amplitude of 10 mV in a frequency range

from 100 kHz to 0.1 Hz. For testing the adsorbed dye amount of the TiO2 working eletrodes, the sensitized-TiO2 samples desorbed the dye into 0.1 M NaOH solution. The measured absorption

spectra were used to calculate the amount of the adsorbed dye amount, expressed in terms of moles of dye anchored per projected unit area of the photoanodes. ADDITIONAL INFORMATION HOW TO

CITE THIS ARTICLE: Chu, L. _et al._ Anatase TiO2 Nanoparticles with Exposed {001} Facets for Efficient Dye-Sensitized Solar Cells. _Sci. Rep._ 5, 12143; doi: 10.1038/srep12143 (2015).

REFERENCES * O’Regan, B. & Gratzel, M. A low-cost, hight-efficiency solar cell based on dye-sensitized colloidal TiO2 film. Nature 353, 737–740 (1991). Article  ADS  Google Scholar  *

Hagfeldt, A., Boschloo, G., Sun, L. C., Kloo, L. & Pettersson, H. Dye-sensitized solar cells. Chem. Rev. 110, 6595–6663 (2010). Article  CAS  PubMed  Google Scholar  * Yella, A. et al.

Electrolyte exceed 12 percent efficiency based redox-porphyrin-sensitized solar cells with cobalt (II/III). Science 334, 629–634 (2011). Article  CAS  ADS  PubMed  Google Scholar  *

Yanagida, S., Yu, Y. H. & Manseki, K. Iodide-free dye-sensitized solar cells. Acc. Chem. Res. 42, 1827–1838 (2009). Article  CAS  PubMed  Google Scholar  * Hardin, B. E., Snaith, H. J.

& McGehee, M. D.The renaissance of dye-sensitized solar cells. Nature Photonics 6, 162–169 (2012). Article  CAS  ADS  Google Scholar  * Ahmad, S. et al. Metal free sensitizer and

catalyst for dye sensitized solar cells. Energy Environ. Sci. 6, 3439–3466 (2013). Article  CAS  Google Scholar  * Chiba, Y. et al. Dye-sensitized solar cells with conversion efciency of

11.1%. Jpn. J. Appl. Phys. 45, 638–640 (2006). Article  Google Scholar  * Sun, Z., Kim, J. H., Zhao, Y., Attard, D., Dou, S. X. Morphology-controllable 1D-3D nanostructured TiO2 bilayer

photoanodes for dye-sensitized solar cells. Chem. Commun. 49, 966–968 (2013). Article  CAS  Google Scholar  * Crossland, E. J. W. et al. Mesoporous TiO2 single crystals delivering enhanced

mobility and optoelectronic device performance. Nature 495, 215–220 (2013). Article  CAS  ADS  PubMed  Google Scholar  * Wu, W. Q. et al. Morphology-controlled cactus-like branched anatase

TiO2 arrays with high light-harvesting efficiency for dye-sensitized solar cells. J. Power Sources 260, 6–11 (2014). Article  CAS  ADS  Google Scholar  * Chen, X. B. & Mao, S. S.

Titanium dioxide nanomaterials: synthesis, properties, modifications and applications. Chem. Rev. 107, 2891–2959 (2007). Article  CAS  PubMed  Google Scholar  * Li, W., Wu, Z. X., Wang, J.

X., Elzatahry, A. A. & Zhao, D. Y. A perspective on mesoporous TiO2 materials. Chem. Mater. 26, 287–298 (2014). Article  CAS  Google Scholar  * Lee, J. W., Lee, J., Kim, C., Cho, C. Y.

& Moon, J. H. Facile fabrication of sub-100 nm mesoscale inverse opal films and their application in dye-sensitized solar cell electrodes. Sci. Rep. 4 (2014). * Liao, J. Y., Lei, B. X.,

Kuang, D. B. & Su, C. Y. Tri-functional hierarchical TiO2 spheres consisting of anatase nanorods and nanoparticles for high efficiency dye-sensitized solar cells. Energy Environ. Sci. 4,

4079–4085 (2011). Article  CAS  Google Scholar  * Park, N. G., van de Lagemaat, J. & Frank, A. J. Comparison of dye-sensitized rutile-and anatase-based TiO2 solar cells. J. Phys. Chem.

B 104, 8989–8994 (2000). Article  CAS  Google Scholar  * Chen, C. D. et al. Microwave-assisted topochemical conversion of layered titanate nanosheets to {010}-faceted anatase nanocrystals

for high performance photocatalysts and dye-sensitized solar cells. Cryst. Growth Des. 14, 5801–5811 (2014). Article  CAS  Google Scholar  * Wu, X., Chen, Z. G., Lu, G. Q. & Wang, L. Z.

Nanosized anatase TiO2 single crystals with tunable exposed (001) facets for enhanced energy conversion efficiency of dye-sensitized solar cells. Adv. Funct. Mater. 21, 4167–4172 (2011).

Article  CAS  Google Scholar  * Fang, W. Q., Gong, X. Q. & Yang, H. G. On the unusual properties of anatase TiO2 exposed by highly reactive facets. J. Phys. Chem. Lett. 2, 725–734

(2011). Article  CAS  Google Scholar  * Chen, J. S. et al. Constructing hierarchical spheres from large ultrathin anatase TiO2 nanosheets with nearly 100% exposed (001) facets for fast

reversible lithium storage, J. Am. Chem. Soc. 132, 6124–6130 (2010). Article  CAS  PubMed  Google Scholar  * Jung, M. H., Chu, M. J. & Kang, M. G. TiO2 nanotube fabrication with highly

exposed (001) facets for enhanced conversion efficiency of solar cells. Chem. Commun. 48, 5016–5018 (2012). Article  CAS  Google Scholar  * Yu, J. G. et al. Anatase TiO2 nanosheets with

exposed (001) facets: improved photoelectric conversion efficiency in dye-sensitized solar cells. Nanoscale 2, 2144–2149 (2010). Article  CAS  ADS  PubMed  Google Scholar  * Fang, W. Q. et

al. Yolk@shell anatase TiO2 hierarchical microspheres with exposed {001} facets for high-performance dye sensitized solar cells. J. Mater. Chem. 22, 22082–22089 (2012). Article  CAS  Google

Scholar  * Yu, J. G. et al. Enhanced photocatalytic CO2-reduction activity of anatase TiO2 by coexposed {001} and {101} facets. J. Am. Chem. Soc. 136, 8839–8842 (2014). Article  CAS  PubMed

  Google Scholar  * Laskova, B. et al. Electron kinetics in dye sensitized solar cells employing anatase with (101) and (0 01) facets. Electrochimica Acta 160, 296–305 (2015). Article  CAS 

Google Scholar  * Mathew, S. et al. Dye-sensitized solar cells with 13% efficiency achieved through the molecular engineering of porphyrin sensitizers. Nature Chem. 6, 242–247 (2014).

Article  CAS  ADS  Google Scholar  * Tao, J., Dong, X., Zhu, H., Tao, H. J., He, P. T. Enhanced photocatalytic properties of ultra-long nanofiber synthesized from pure titanium powders. Rare

Metals 31, 39–42 (2012). Article  Google Scholar  * Tian, F., Zhang, Y. P., Zhang, J. & Pan C. X. Raman spectroscopy: a new approach to measure the percentage of anatase TiO2 exposed

(001) facets. J. Phys. Chem. C 116:13, 7515–7519 (2012). Article  Google Scholar  * You, T., Jiang, L., Han, K. L. & Deng, W. Q. Improving the performance of quantum dot-sensitized solar

cells by using TiO2 nanosheets with exposed highly reactive facets. Nanotechnology 24, 245401–6 (2013). Article  ADS  PubMed  Google Scholar  * Li, H. M. et al. Hierarchical TiO2

nanospheres with dominant {001} facets: facile synthesis, growth mechanism and photocatalytic activity. Chem. Eur. J. 18, 7525–7532 (2012). Article  CAS  PubMed  Google Scholar  * Yang, H.

G. et al. Anatase TiO2 single crystals with a large percentage of reactive facets. Nature 453, 638–642 (2008). Article  CAS  ADS  PubMed  Google Scholar  * Zhu, K., Neale, N. R., Miedaner,

A. & Frank, A. J. Enhanced charge-collection efficiencies and light scattering in dye-sensitized solar cells using oriented TiO2 nanotubes arrays. Nano Lett. 7:1, 69–74 (2007). Article 

ADS  Google Scholar  * Liao, J. Y., Lin, H. P., Chen, H. Y., Kuang, D. B. & Su, C. Y. High-performance dye-sensitized solar cells based on hierarchical yolk-shell anatase TiO2 beads. J.

Mater. Chem. 22, 1627–1633 (2012). Article  CAS  Google Scholar  * Tian, J. J. et al. Architectured ZnO photoelectrode for high effciency quantum dot sensitized solar cells. Energy Environ.

Sci. 6, 3542–3547 (2013). Article  CAS  Google Scholar  * Wang, Q. et al. Characteristics of high efficiency dye-sensitized solar cells. J. Phys. Chem. B 110, 25210–25221 (2006). Article 

CAS  PubMed  Google Scholar  * Zaban, A., Greenshtein, M. & Bisquert, J. Determination of the electron lifetime in nanocrystalline dye solar cells by open-circuit voltage decay

measurements. Chem. Phys. Chem. 4, 859–864 (2003). Article  CAS  PubMed  Google Scholar  * Bisquert, J., Zaban, A., Greenshtein, M. & Mora-Seró, I. Determination of rate constants for

charge transfer and the distribution of semiconductor and electrolyte electronic energy levels in dye-sensitized solar cells by open-circuit photovoltage decay method. J. Am. Chem. Soc. 126,

13550–13559 (2004). Article  CAS  PubMed  Google Scholar  * Wang, Z. S., Kawauchi, H., Kashima, T. & Arakawa, H. Significant influence of TiO2 photoelectrode morphology on the energy

conversion efficiency of N719 dye-sensitized solar cell. Coord. Chem. Rev. 248, 1381–1389 (2004). Article  CAS  Google Scholar  * Jang, I., Song, K., Park, J. H. & Oh, S. G. Enhancement

of dye adsorption on TiO2 surface through hydroxylation process for dye-sensitized solar cells. Bull. Korean Chem. Soc. 34, 2883–2888 (2013). Article  CAS  Google Scholar  Download

references ACKNOWLEDGEMENTS We acknowledge the financial support from the National Basic Research Program of China (2012CB933301, 2014CB648300), the Ministry of Education of China (No.

IRT1148), the National Synergistic Innovation Center for Advanced Materials (SICAM), the Natural Science Foundation of Jiangsu Province of China (BM2012010), the Project Funded by the

Priority Academic Program Development of Jiangsu Higher Education Institutions (YX03001) and the National Natural Science Foundation of China (51172110, 51372119). AUTHOR INFORMATION AUTHORS

AND AFFILIATIONS * School of Science, Nanjing University of Posts and Telecommunications (NUPT), 210046, Nanjing, P.R. China Liang Chu & Jianping Yang * Key Laboratory for Organic

Electronics & Information Displays (KLOEID) & Institute of Advanced Materials (IAM), Jiangsu National Synergistic Innovation Center for Advanced Materials (SICAM), School of

Materials Science and Engineering (SMSE), Nanjing University of Posts and Telecommunications (NUPT), Nanjing, 210046, P.R. China Zhengfei Qin & Xing’ao Li Authors * Liang Chu View author

publications You can also search for this author inPubMed Google Scholar * Zhengfei Qin View author publications You can also search for this author inPubMed Google Scholar * Jianping Yang

View author publications You can also search for this author inPubMed Google Scholar * Xing’ao Li View author publications You can also search for this author inPubMed Google Scholar

CONTRIBUTIONS L.C. carried out all experiments, devised the original concept and wrote the draft of the manuscript; Z.F.Q. participated in discussion of results; J.P.Y. & X.A.L.

discussed the interpretation of results and revised the manuscript. All authors discussed the results and participated in manuscript revision. J.P.Y. & X.A.L. are corresponding authors.

ETHICS DECLARATIONS COMPETING INTERESTS The authors declare no competing financial interests. ELECTRONIC SUPPLEMENTARY MATERIAL SUPPLEMENTARY INFORMATION RIGHTS AND PERMISSIONS This work is

licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license,

unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce

the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/ Reprints and permissions ABOUT THIS ARTICLE CITE THIS ARTICLE Chu, L., Qin, Z., Yang, J. _et

al._ Anatase TiO2 Nanoparticles with Exposed {001} Facets for Efficient Dye-Sensitized Solar Cells. _Sci Rep_ 5, 12143 (2015). https://doi.org/10.1038/srep12143 Download citation * Received:

25 March 2015 * Accepted: 18 June 2015 * Published: 20 July 2015 * DOI: https://doi.org/10.1038/srep12143 SHARE THIS ARTICLE Anyone you share the following link with will be able to read

this content: Get shareable link Sorry, a shareable link is not currently available for this article. Copy to clipboard Provided by the Springer Nature SharedIt content-sharing initiative